PLA-D6L
PLA-D6L is a RFID proximity card reader from the Unique (EM4102), HITAG1/S, HITAG2, HID ISOProx®II and Q5 families operating at 125kHz.
Reader is equipped with 1-Wire® (Dallas DS1990 emulation), Wiegand and serial UART (CMOS), RS-232-CMOS interfaces. The reader is equipped with a 1m long cable terminated with a male 2x3-pin Molex MicroFit3.0 plug. The reader has a built-in antenna, buzzer and two LED indicators. It has been designed in accordance with the requirements of the E-mark automotive safety standard.
Reader has the following functionalities:
- Supports RFID transponders from the Unique (EM4102), HITAG1/S, HITAG2, HID ISOProx®II families operating at 125kHz,
- 1-Wire (DS1990 emulation) and Wiegand interfaces,
- UART (CMOS), RS-232-CMOS serial interfaces,
- Low energy consumption,
- Wide range of input supply voltage,
- Built-in antenna, buzzer and two LED indicators for status,
- Software update via interface,
- Configuration using a button or a protocol,
- Compact, flat housing,
- Designed in accordance with the requirements of E-mark.
PLA-D6L is the direct successor of the PLA-UDK and PLA-2DK readers, which goes into EOL status and are not recommended for use in new applications.
| Series | PLA |
| Operating frequency | 125kHz |
| Supported standards | HID ISOProx®II HITAG 1 HITAG 2 HITAG S Q5 Unique (EM4102) |
| Interface | 1-Wire® RS-232 (CMOS) UART (CMOS) Wiegand |
| Read range | up to 8cm* |
| Avg. current consumption | up to 5mA (for 1-Wire, Wiegand) up to 12mA (for serial intefaces) |
| Antenna | Yes |
| LED | Yes |
| Buzzer | Yes |
| Relay | No |
| Operating temperature | -20°C to +65°C |
| Size (mm) | 54 x 85 x 7 |
| Cable length | 100 cm |
| Connector | 2x3-pin male Molex MicroFit 3.0 type |
| Type | RFID reader |
| E-mark compliance | Yes** |
-
- ** It has been designed in accordance with the requirements of the E-mark automotive safety standard.
- * Depends on transponder type.
Gamma Sp. z o.o.
Kacza 6A01-013 Warszawa
Polska
- 22 862 75 00
- info@gamma.pl
Transfer Multisort Elektronik Sp. z o.o.
Ustronna 4193-350 Łódź
Polska
- 42 645 55 55
- dso@tme.pl
SOS electronic s.r.o.
Pri prachárni 16040 11 Košice
Słowacja
- sales@soselectronic.com
Looking for customized version of this product?
Apart from the offer of universal RFID readers and modules available permanently in the offer Netronix provides RFID design services for individual customer requirements. This enables creation of RFID device to be tailored to the specific RFID application.
If you have any questions about design of RFID devices please contact us by e-mail at netronix@netronix.pl.
Related articles
Learn more about our products and technologies behind them.
MIFARE® DESFire reader - why is choosing it so important?
The MIFARE® DESFire® standard is ideally suited for integrators and system operators building reliable, interoperable and scalable proximity solutions. The DESFire standard will seamlessly integrate with mobile systems and can support multi-application smart card solutions in applications for credentials, access control, loyalty programs and micropayments, as well as in public transport ticketing installations.
Are you looking for custom RFID products?
In addition to the offer of universal modules and RFID readers, which are permanently available in the offer
Netronix provides services of designing RFID devices for individual orders.
Thanks to this, it is possible to closely match the designed RFID device to the specificity of the target application.